Firearm Parts

KICK-EEZ® SLIP-OVER RECOIL SYSTEM combines a specifically engineered slip-over pad with the unsurpassed recoil absorbing properties of a Sorbothane® insert. The KICK-EEZ® SLIP-OVER RECOIL PAD is designed for all shooting applications and with...

This recoil pad was designed with an elliptical hole especially for those difficult to fit stocks such as Benelli (including synthetic), the Browning Gold, the Beretta 390 and many other problem fittings. The hole spacing on the Special Slotted Series...

Basically the same contour lines as the All Purpose recoil pads except the heel is canted approximately 45º to allow easier shouldering from “low gun” position.  

Length: 1 3/4" Weight: .3oz Finish: anodized aluminum This handle is made to work with our guide rod and spring kit. The bolt handle length is 1 3/4", which is 1/4" longer than the factory bolt handle giving greater clearance for the shooter's knuckles...

Length: 1 3/4", Weight: .4oz, Finish: anodized aluminum with cushion This handle is made to work with our guide rod and spring kit. The bolt handle length is 1 3/4", which is 1/4" longer than the factory bolt handle giving greater clearance for the...

Length: 1 3/4" Weight: .6oz Finish: stainless steel This handle is made to work with our guide rod and spring kit. The bolt handle length is 1 3/4", which is 1/4" longer than the factory bolt handle giving greater clearance for the shooter's knuckles...

Length: 1 3/4" Weight: .6oz Finish: stainless steel with cushion This handle is made to work with our guide rod and spring kit. The bolt handle length is 1 3/4", which is 1/4" longer than the factory bolt handle giving greater clearance for the...

10/22® style aftermarket slip fit receiver Durable anodized finish Billet aluminum Rear access cleaning hole Optional v-block, rear tang, take down screw, bolt buffer, and pins Specialized interchangeable scope base Receiver comes standard with Zero...

10/22® style aftermarket slip fit receiver Durable anodized finish Billet aluminum Rear access cleaning hole Optional v-block, rear tang, take down screw, bolt buffer, and pins Specialized interchangeable scope base Receiver comes standard with Zero...

Upgrade accessory for the 10/22® bolt Achieve consistent ignition Positive rim indentation Properly hardened steel Precision ground and wire EDM cut holding 0.0001" tolerance Eliminate irregular rim indentation due to a blunt or improper firing...

Replacement part for the 10/22® magazine latch (B-34) Upgrade to an easily interchangeable system Long or medium length levers Machined from billet- anodized for durability Upgrade to the KIDD Interchangeable Magazine Release System for the...

Aftermarket fluted lightweight pistol barrel for the 10/22® Weight: 10" =1 lb Barrel diameter: .920” for 2" then steps to .870" Stainless steel core construction Hand lapped individually 11-degree crown, 1:16 twist, convex extractor...

Aftermarket fluted lightweight pistol barrel for the 10/22® Weight: 10" =1 lb Barrel diameter: .920” for 2" then steps to .870" Stainless steel core construction Hand lapped individually 11-degree crown, 1:16 twist, convex extractor...

Accessory for the KIDD "Trigger Job" Kit Adjust your trigger weight to fit your needs Replaces B-40 plunger spring in Ruger® 10/22® polymer trigger Use the weight tuning springs to set the desired breaking weight in the 10/22® trigger with...

Upgrade your 10/22® receiver with our threaded pins Includes 82 degree countersink-for slight alteration of the receiver Eliminates excessive factory tolerance of pin to receiver fit. Stabilizes trigger guard to greatly enhance bedding stability...

Internal upgrade for your polymer 10/22® trigger guard Complete with Hammer, Sear, Disconnect, and Trigger Blade No Filing or Stoning! From a cumbersome trigger break to a clean one- 20 minutes Pull weight 2.25 lbs Upgrade your polymer factory...